New England Coating Concepts is an outstanding finish supplier.....

Stock colors

• Computer Beige ...... F63 H 10
• Modular Ivory..... F63 H 11
• Spectro Blue ......... F63 L 14
• Circuit Blue ...... F63 L 16 7B
• Gray  F63 A 13 ASA 61
• Gray ......... F63 A 31
• Static Black .......... F63 B 13 *

* Contains Lead

• Turbine Orange .... . ... F63 E 3
• Vista Green  F63 G 18
• Thermal Red ......... F63 R 12
• Ultrasonic Chrome ..... F63 S 1
• Strobe White. . . ...... F63 W 13 *
• Beta Yellow.. F63 Y 8 *

CHARACTERISTICS SPECIFICATIONS

Coating Services,Surface Preparation: Metals:

• Chemical treatment or conversion coating gives best adhesion and performance properties.

• See Metal Preparation Brochure, CCT1.

Iron or Steel: Untreated Metal: Prime with Industrial Wash Primer P60 G 2. For smoother finish, follow with POLANE Primer Sealer E65 A 4. For best corrosion resistance on untreated iron or steel prime with Catalyzed Epoxy Prime E61 RC 22/V66 TC 1 instead of Industrial Wash Primer, P60 G 2.

Treated Metal: For best performance, prime with POLANE Primer Sealer E65A4. Check for adhesion.

Aluminum and Galvanized Steel (Untreated): Prime with Industrial Wash Primer, P60 G 2.

Cast Iron: Fill with POLANE" Spray Fill and sand. For structural steel and heavy duty industrial maintenance applica­tions, sand blast and prime with TILE-CLAD II Primer B62 N 71/860 V 70 at 4-5 mils dry film thickness.

 
Plastic: Coating must be evaluated on customer substrate. Filler or barrier coat may be required.

Wood:Interior only. Surface must be dry, sanded, and dust free, Seal with Full coat of POLANE(R' Spray Fill and sand. See Product Data Sheet CC-D1.

Coating Services, Performance Tests:

1. Salt Spray - 250 hours ......... . Excellent. 1/8" rust creepage on scribe max.
2. Humidity-100% R.H. @a 100°FPass 200 hours.
3. Water immersion - 100 hours.
4. Lacquer thinner, acetone, MEK, gasoline, xylene - 20 double rubs with saturated cloth.
5. Lubricating oils, hydraulic fluids and cutting oils.
6. Cold Check: 16 cycles; 24 hours @ 100% humid­ity; 24 hours at 10°F. 24 hours at 77°F.
7. Pencil hardness H to 2H.
8. Flexibility - 1/8" conical mandrel.
9. Taber abrasion - CS 17 wheel, 1,000 gm. load: <100 mg. loss/1,000 cycles.
10. Impact resistance: Forward 100 inch pounds. Reverse 80 inch pounds.

Catalyze six parts POLANE' B POLYURETHANE ENAMEL to one part POLANE(" Catalyst V66V27 or V66 V 29.

 
Reduction:

Reduce three parts catalyzed material with one part of POLANE (" Reducer R7 K 69 (Photo chemically Reactive) or POLANER, Reducer R7 K 84 Non­photo chemically Reactive). For more flow, use POLANE Retarder R71<216.

Recommended Film Thickness:
Wet - 4-5 mils, Dry - 1.0-1.25 mils Spraying: Apply with standard equipment- pressure or suction feed, airless or electrostatic equipment.

 
Pressure Feed:
Use DeVlbiss MBC gun with Etipand needle and No. 765 air cap, or equivalent. 8 to 10 psi fluid pressure. Use 40-45 psi atomizing pressure:
Suction Feed:
Use DeVilbiss MBC gun with E tip. needle and No. 30 air cap or equivalent. 40-45 p.s.i. atomizing pressure.
Gloss Adjustments:
Gloss can be lowered by intermixing with POLANE Flat­tening Paste F63 T 1.
POLANE Gloss Enamel ........ 6 5 4
POLANE Flattening Paste ... 0 1 2
Gloss at 60 degrees (approximately)  90   40   10
Product Limitations:
1. POLANE° B POLYURETHANE ENAMEL coatings MUST BE CATALYZED at 6:1 ratio.
2. Use POLANE CatalystV66V27forinterior use. V66 V 27 will lead to early chalking and gloss loss on exterior exposure. Use POLANE Catalyst V66 V 29 for exterior exposure applications. POLANE19 B catalyzed with V66 V 29 is not intend­ed for long-term exterior exposure because ex­tended exposure to strong sun intensity will lead to chalking, gloss loss and color fading.
3. Do not spray hot. Heat shortens pot life. Do not
pump catalyzed material from drums into cir­culating system. Friction heat developed by pumps and circulation will shorten pot life.
4. Dip, flo-coat and brushing are not recommended.
5. DO NOT VARY CATALYST RATIO. The catalyst ratio has been established for optimum hardness, flex­ibility, gloss and chemical and solvent resistance. Slight over or under catalyzation will not seriously affect performance.
6. Because of many types and compositions of plastic available, each user should test on his substrate before production use. Consult your SHERWIN-WILLIAMS Representative for addi­tional information.
7. Curing temperature must not exceed the heat distortion temperature of the plastic substrate.
8. Protect POLANE Enamels, Catalyst, and Reducer from moisture as water affects pot life and properties. Store indoors.
9. Do not package POLANE coated products in air­tight plastic bags unless completely cured. Since POLANE° Enamels continue to cure for several weeks, the buildup of organic solvents and reac­tion by-products could cause improper cure and adhesion failure in use.
10. Do not blend with any Polyurethane quality other than POLANE B and POLANE T No other catalysts, colorants or reducers are recommended because foreign materials such as alcohol sand glycols destroy performance properties. Lacquer thinners and alcohol containing solvent blends should not be used with POLANE enamels.
11 . If recoated after 7 days room temperature cure, scuff sand to insure proper inter coat adhesion. 12. Do not apply to wood substrates for exterior applications.
 
Note: The information, rating and opinions stated above per­tain to the material currently offered and represent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application which are not known or not under our control, The Sherwin-Williams Company cannot make any war­ranties or guarantees as to the end result.
Note. For EMI shielding specifications go to shielding in left column.
Clean Up:
Use POLANE Reducer R7 K 69 or R 7 K 84 following supplier’s safety recommendations.

PRODUCT CC-DATA D5  
POLANE® T POLYURETHANE ENAMEL
FOR TEXTURED FINISHES
PRODUCT DESCRIPTION
Profile Gray .......... F63 A 33 Carbide Black ........ F63 B 12 • Decibel Orange ....... . F63 E 4 • (contains lead)
Precision Tan ........ F63 H 12 Instrument Tan ....... F63 H 13 Nitro Blue ........... F63 L 17
Flatting Paste ......... F63 T 1 Linear White ......... F63 W 12

CHARACTERISTICS SPECIFICATIONS
POLANE T is a two component low gloss polyurethane coating providing superior ap­pearance and durability. POLANE Enamels are used either as smooth or textured coatings.
Advantages:
1. Excellent appearance over many types of substrates- metal, plastics, and wood.
2. Air dry or force dry.
3. Excellent chemical and water resistance.
4. Excellent adhesion, mar, and abrasion resistance.
5. Excellent hardness and impact resistance.
6. Widely used for coating of business machines and computers because of resistance to stains, chemicals, abrasion and for long-term durability.
7. Texturing minimizes surface irregularities and provides 3-Dimensional appearance.
8. Non-photo chemically reactive.
9. Full range of colors may be blended.
10. Lower glosses may be obtained by using POLANE Flatting Paste, F63 T 1.
11. Versatile uses. In addition to traditional materials, such as sheet metal, POLANE  T is easily adaptable to the finishing of newer structural plastics that cannot tolerate normally high baking tem­peratures without distortion, pin holing or blistering. Its textured appearance camou­flages imperfections left by production opera­tions such as grinding marks, welding seams, and molding. A list of POLANE T applica­tions would include products as diverse as computer housing and burial caskets, mea­suring instruments and dental equipment, sewing machines and snowmobiles medical equipment ect...
Note: The information, rating and opinions stated above pertain to the material currently offered and repre­sent the results of tests believed to be reliable. However, due to variations in customer handling and methods of application which are not known or under our control, The Sherwin-Williams Company cannot make any warranties or guarantees as to the end result.
 
Performance Tests:
The tests below were conducted on Bonderite 1000 panels at 1 mil dry film after 30 days air dry. Each rated excellent or no failure.
1. 5% Salt Spray - 500 hours.
2. 100% relative humidity - 500 hours.
3. Water immersion - 100 hours.
4. Lacquer thinner, acetone, gasoline, MEK, xylol - 20 rubs with saturated cloth.
5. Lubricating oil, hydraulic fluids and cutting oils.
6. Cold Check: 16 cycles; 24 hours @ 100% humidity; 24 hours at 10°F. 24 hours at 77'F.
7. Pencil hardness H to 2H.
8. Flexibility 1/8" conical mandrel.
9. Taber abrasion-CS 17wheel,1000 gm. load: < 100 mg. loss/1000 cycles.
10. Impact resistance: Forward 100 inch pounds, Reverse 80 inch pounds.
Note. For EMI shielding specifications go to shielding in left column.
Coating Services For EMI Shielding and Polyurethane Finishes!
 

Home•About Us•Sprayed On Polyurethane•Metal Finishing•EMI Shielding•Metalizing•Conductive Coating•Plastic Finishing•Conformal Coating•RFI Shielding•Polyurethane Spray Coating•Shielding•Finishes•Contact Us•Sitemap